Newest Diagbox V7.83 Lexia3 PP2000 Firmware 921815C Lexia 3 For Citroen For Peugeot Car Diagnostic Tool Free Ship
LITE Lexia3 With golden edge+12PCS Japan NEC RELAY + 2PCS OPTOCOUPLERS
Full Chips Lexia3 With Golden Edge + 12PCS Japan NEC RELAY + 7PCS OPTOCOUPLERS:
1. If you need V7.83 software, we will send you software link.
2. Softwares need install on Win7 32Bit Only. These three softwares can not install on same laptop. You need install on different laptop individually. Diagbox software include lexia and PP2000. Your laptop system requires at least Intel Celeron/Pentium III 400 MHz,128 MB RAM,50MB free HDD space and USB 1.1 port (USB 2.0 recommended)
3. Please remeber to shut down your anti-virus software And then disconnect the internet Before install the software. If you do not know how to install it, please watch our video first.
4. Diagbox Update Attention: please cut the file “C:AWRootbinfiAPPDIAG.SYS” out before update, and then click update package! after complete update please paste the cutted file back into the previous folder. which can avoid activating problem.
Diagbox Software Update Password:
Diagbox V7.XX to V7.76: scary01
Diagbox V7.76 to V7.82: Maitresox01
Diagbox V7.82 to V7.83: Very Simple!
5. For programming, diagbox support basic programming, but some programming like car alarm system need account username and password, we don't supply& haven't username and password, only for citr-oen and peu-geot center repair shop has username and password, please note it.
Firmware: Normal Version Full Chip 921815C With 12PCS JAPAN NEC Relay+2PCS OPTOCOUPLERS
Software: Lexia3 V48, PP2000 V25, Diagbox V7.83
2. Lexia 3 PP2000 works with most of forCitroen and forPeugeot cars from 1995 to 2015.
3. Functions: read identification, read fault codes, clear fault codes,auto-scan etc.
lexia 3 dealers diagnostic scanner for comprehensive for Citr-oen and (Peu-eot) cars. You can do all as an authorized Dealer does. This diagnostics software allows you to perform complete diagnostics of all from 1995 till present models. Diagnostics is performed via OBD II connector (which is located near steering wheel) or via manufacturer-specific connector (only older cars, pre-2001).
Unlike other universal car scanner tools which only read fault codes;this software performs nearly ALL the functions like the original dealer diagnostic tool. Our diagnostic interface contains K-Line multiplexor,CAN-BUS interfaces and SAE J1850 bus (both PWM and VPW).
Displays complete identification of control unit, e.g. part number,software/hardware version, manufacturer, etc…
2. Read fault codes
Displays all stored and pending fault codes with complete description (e.g. “Rail pressure – too low pressure”).
Program supports report printing or copy to clipboard.
3. Clear fault codes
This function clears all stored fault codes and other diagnostic information.
4. Auto-scan (complete car scan/test)
Detects all ECUs (electronic control units) installed in car and reads all diagnostic fault codes.
5. Measured Values
Program displays live Data like Engine Speed,Battery voltage,Oxygen Sensor,Coolant Temperature, etc.Values can be displayed in graph, 9 values at once, or full listing (all measured values).Logging to file is also supported,which allows offline analysis.
6. Actuator test
Actuator test activates particular actuator (e.g. turn on fuel pump, lock/unlock wheel, lock/unlock doors, cut off fuel, etc..)
Compatible Vehicles List:
For Citroen: for CZERO, C1, C2, C3 DS3, C4, DS4, C5, C6, C8, for C-CROSSER, for NERO, for BERLINGO, for JUMPY, for AX, for SAXO, for BX, for ZX,for XSARA, for XANTIA, for XM, for EVASION, for C15
For Peugeot: ion, 107, 206, 207, 307, 308, RCZ, 407, 508, 607, 807, 1007, 3008, 4007, 5008, for BIPPER, for PARTNER, for EXPERT, for BOXER, 106, 205, 306, 309, 405, 406, 605, 806
1pc x Main Unit
1pc x Long 9pin to USB cable
1pc x Short 9pin to USB cable
1pc x CD
1pc x Clip Cable